T value of a single subject

1 min read

I usually report a group-level T-test image in the final publications or presentations. But in the early stage of a project when only one or a few subjects have been scanned, I often need to report an activation map for an individual subject after general linear model analysis (GLM). I could show a beta image or activation image, but a T-image is sometimes desired. The question is how do I calculate the T-value of a contrast for a single subject.

I will use the following example to show how it is calculated. Assume we have two conditions, beep and flash, and the brain signal is saved in y. Based on the timing of beep and flash, we have an independent variable called x with two columns. The 1st column is for beep, the 2nd for flash.

x=rand(10,2);
y=x(:,1)*2 + x(:,2)*3 + 0.2 + rand(size(x(:,1)))/5;
[a,b,c] = glmfit(x,y);

Now you can easily find the beta value, the T value, and the p-value of each individual condition:

beta = a(2:end)'
T = c.t(2:end)'
p = c.p(2:end)'

What about the contrast between beep and flash? Well, it’s a bit more complicated. First, we need to find the covariance matrix of the betas.

covb = c.covb(2:end, 2:end);

Then we define our contrast vector, in this case it is simply contrast = [1 -1]. The variance of contrast (beep-flash) is

V = contrast  * covb * contrast';

The T-value of the contrast is

T = (beta * contrast') / sqrt(V) * sqrt(length(x)); 

Note: you might be tempted to use the two-sample T formula to calculate the T-value (i.e. finding the variance of beta1, variance of beta2, and then calculate). It is not the correct way. We have to consider the case where the two conditions are correlated. Using the covariance matrix above is the right way.



写作助手,把中式英语变成专业英文


Want to receive new post notification? 有新文章通知我

第五十期fNIRS Journal Club通知2024/03/30, 10am 王一晖

早期的 STEM 教育对于以后的学习至关重要。现有研究尚未就STEM教学法达成共识,学生先验知识对基于故事的STEM教学法的影响还有待探讨。来自澳门大学张娟教授团队的王一晖将会分享基于fNIRS超扫描
Wanling Zhu
9 sec read

第四十九期fNIRS Journal Club视频 高倩博士

Youtube: https://youtu.be/a2QlCFZUytA优酷: https://v.youku.com/v_show/id_XNjM3MjMyNjUxMg==.html 竞技比赛中,
Wanling Zhu
12 sec read

第四十九期fNIRS Journal Club通知2024/02/24, 10am 高倩博士

竞技比赛中,特别是需要注意高度集中的射击项目中,如何保持稳定的注意控制对运动员的表现至关重要。近期的一项研究调查了赛前短时正念练习是否对运动员在射击比赛中的注意控制具有提升作用。来自北京体育大学心理学
Wanling Zhu
9 sec read

6 Replies to “T value of a single subject”

  1. Hi,Cui Xu. Whether the values of c.t are the T-values of the contrast (beep-baseline or flash-baseline) ?

  2. Sir, Thanks for your wonderful explanation on how to calculate the T-value for an individual subject. My questions is if I assume there are four conditions and I need to find the contrast between these conditions, what would be the contrast vector in this case? Is it [+1 +1 +1 -3]?

  3. Hi Profesor Xu Cui

    I have been following your blog since I began my Bachelor Thesis about fnirs and it has been very insightful to me.
    I ran finger tapping experiments using a block-design of 20 repetition with the task of 10 (s) and a rest time of 15 (s)between task.
    Every time a cue appeared on the screen the subject performed 10 s of finger tapping.

    Now, I want to apply a statistical result at subject level. I am trying to apply the GLM as you described here. However, I am struggling with 3 questions.

    – Before applying the GLM, it is better pre-processing my signal. Such as, baseline correction, downsampling, band-pass filtering to remove artifacts and lately apply MBL to obtain Hemoglobin concentration change as a time series o it is not necessary the pre-processing before the GLM?
    I asked because the papers I saw it do not clarify this point.

    -How properly design the matrix design. I defined it using the following code:

    % EXPECTED HRF
    t = 1:1:13;
    h = gampdf(t,6) + -.5*gampdf(t,10); % HRF MODEL
    h = h/max(h); % SCALE HRF TO HAVE MAX AMPLITUDE OF 1

    nTRs=7182;
    Experiment_time=0:1/9.7:(nTRs-1)/9.7;
    impulseTrain0 = zeros(length(Experiment_time),1);

    %CUE ONSET
    cue=[1270 1567 1865 2163 2461 2759 3056 3354 3652 3950 4248 4546 4843 5141 5439 5737 6035 6332 6630 6928];

    % FINGER TAPPING
    impulseTrain0(cue)=1;

    % EXPERIMENT DESIGN / STIMULUS SEQUENCE
    D = [impulseTrain0];

    % CREATE DESIGN MATRIX FOR THE THREE STIMULI
    X = conv2(D,h’); % X = D * h
    X(nTRs+1:end,:) = []; % REMOVE EXCESS FROM CONVOLUTION

    – ¿How make up a contrast vector with just one condition? As you notice, my experiment just has one condition(Tapping). so, if I want to compare the condition with the baseline in order to know if the activation is statistical significant how can create a contrast.

    Sorry if my questions were too long.

    Thanks
    Agustin

Leave a Reply to Jana Cancel reply

Your email address will not be published. Required fields are marked *